Parker THC
Dakota Fluid Power is a Parker THC... and because of our status as a THC, we carry a comprehensive
Truck Parts inventory available for you at any of our locations. Other Parker parts are available upon order.
Pneumatic Valves
• Extreme operating conditions, -40°F to 158°F temperature 
rating & 232 max pressure rating
• Solenoid, manual & remote pilot options available
• 1/8" thru 1/2" ports sizes standard in both inch and metric
Hydraulic Valves MV3/5 Series
• Open-center design, stackable configuration 
• Flows 6-10 GPM, 3000 PSI
• Manual operation
• Compact package
Power Take-Off 8-Bolt 880 Series
• Two gear
• Coverage for tough applications
• Speed ratios for high / low speed applications
• Removable shift cover for adjusting backlash
• Dual-pump output for mounting a pump on each
end of PTO
Power Take-Off 6-Bolt 442 Series
• Two gear
• Engineered to work with most existing transmission applications
• Economical workhorse features cast iron housing
• Tapered cone bearings for high torque rating / long service life
• Slip fit idler pin for easy interchange from one transmission to another
• Easy to set backlash
• Wide range of shift / output options
Gear Pump/Motors PGP050/051, PGP075/076, PGP505/511 Series
• Three-piece cast iron construction 
• Heavy duty application
• Long life in severe environments
• Single, multiple or piggyback assemblies
• Variety of valve options
• Can be configured as a pump or motor
Gear Pump/Motors PGP315/330/350/365 Series
• 315, 330, 350 and 365 frame sizes
• Single, multiple, piggyback, Add-APump 
• Pumps, motors, flow dividers
• Relief valves, priority valves, load sense unloading
• 0.47 – 9.00 in3/rev (7.6 – 147.5 cc/rev)
• Pressures to 3500 PSI• Speeds to 3000 rpm
Gear Pump/Motors PGP020 Series
• Rugged cast iron body
• Variety of drive shafts and mounting styles
• Flows: up to 29 GPM/2400 rpm /3000 PSI; up to 39 GPM/2400 rpm /2500 PSI
• Can be assembled in tandem
• Can be configured as a pump or motor PGP500 Series
• High performance / efficiency
• Low noise at high operating pressures
• International mounts and connections
• Integrated valve capabilities
• Common inlet multiple pump configurations
• Can be configured as a pump or motor
Power Take-Off 8-Bolt 489 Series
• Two gear
• 442 Series family, but with an 8-Bolt mounting flange
• No adapter plate needed
• Less installation time, less expense, and less chance of leakage
• Wide range of shifter options / pump flangesPower Take-Off 10-Bolt 277/278 Series
• Approved for use with Allison World Transmissions
• (277 Series) Five speed ratios and eighteen output options
• (278 Series) Six speed ratios and eighteen output options
• (278 Series) Enhanced housing design for maximum transmission clearance when
direct mounting a pump
• SuperTorque™ gears available for 20% higher intermittent torque ratings
• Electronic overspeed control available to protect driven equipment from over-speeding
• Electric / hydraulic shift
Power Take-Off 10-Bolt 277/278 Series
• Approved for use with Allison World Transmissions
• (277 Series) Five speed ratios and eighteen output options
• (278 Series) Six speed ratios and eighteen output options
• (278 Series) Enhanced housing design for maximum transmission clearance
when direct mounting a pump
• SuperTorque™ gears available for 20% higher intermittent torque ratings
• Electronic overspeed control available to protect driven equipment from over-speeding
• Electric / hydraulic shift
• Internal bearing lube
Gear Pump/Motors C101/102 and G101/102 Series
• Pump / valve combinations
• Remote / PTO Mount
• Two / three-line installations
• Air remote operators option
• 138 bar (2000 PSI) relief valve Std.
• Pressures to 172 bar (2500 PSI)
Wet Line Kits, Reservoirs and Accessories
• Simple to use software builds complete Wet Line System – saves time
• Uses Parker, Commercial and Chelsea quality components
• Single part numbered kits for immediate installation
• Software provides a Bill of of Material used to order repair / replacement parts
• Takes the guesswork out of system design
Hydraulic Cartridge Systems PSM1000, PSM1500
• Spreader control system provides remote electronics for a safer quieter cab environment
• Non-ground speed system and operates in open loop only
• Feed rate proportional cartridge 16 GPM
• Spinner proportional cartridge 7 GPM
• Manual over-rides
• Proportional unloader for fixed displacement pumps
• System safety relief
• Standard SAE ports
• 3000 PSI operation
• Main power button
• Feed rate potentiometer – 10 detents
• Spinner potentiometer – 10 detents
Hydraulic Valves V20 Series
• Open-center design, stackable configuration
• Flows 10-25 GPM, 3500 PSI
• Work ports available in SAE 8, 10 and 12
• Very competitive open-center and loop pressure drops
• Electro-hydraulic package includes integrated “on-demand” pressure generation and regulation
• Work-section EH options include a single-ended cap design that permits manual both sides of the truck and/or radio remote |
